In this video, see how to access solid subobjects by holding the CTRL key. You can also use Dynamic UCS mode to sketch a line and PRESSPULL to alter a solid object.
- [Instructor] Right now, this stair is open…on this side, so that you could actually…fall off of the stair, and it would…present somewhat of a hazard.…And so, now, we need to build a low wall.…And we have a representation here in the plan…where that wall would go.…So, let's start by creating a new layer…and call it - Wall - Low.…And I'll set that as the current layer.…I'll also change it's color.…Let's make it a dark red.…And then, I'd like to draw a rectangle…on the ground, but right now, the UCS is set…so that the XY plane is parallel to this red wall, here.…
So, I need to reset the UCS back to the original…coordinate system called, the World System.…To do that I'll type USC, Enter, Enter.…So now, the XY plane is on the ground.…I'll go ahead and draw a rectangle…going from this corner over to…this opposite corner, right here.…And then, I'll extrude the last object…that was created by typing L, Enter, Enter.…
Exit from selection mode.…And now, I'm into the extrusion process.…So, I'm going to extrude this all the way up to the top…
Author
Released
1/3/2019- Arranging elevations and sections around a plan
- Rotating objects in 3D
- Extruding walls, interior partitions, and headers
- Building slabs
- Modeling doors, windows, and stairs
- Sculpting terrain
- Creating a second floor
- Building roof surfaces
- Sculpting solids from regions and surfaces
- Modeling a tower
Skill Level Intermediate
Duration
Views
Related Courses
-
AutoCAD: 2D & 3D Elevations
with Shaun Bryant2h 58m Intermediate -
AutoCAD: Construction Drawings
with Shaun Bryant3h 18m Intermediate -
AutoCAD Add-ins Using VB.NET
with Josh Modglin4h 26m Intermediate -
AutoCAD: Advanced Workflow with Sheet Sets
with Shaun Bryant2h 52m Intermediate
-
Introduction
-
What you should know1m 16s
-
1. Clean Up 2D Drawings
-
2. Model the Ground Floor
-
Navigate in 3D5m 55s
-
Rotate objects in 3D3m 40s
-
Extrude interior partitions2m 53s
-
Model curved headers3m 30s
-
Build the slab on grade4m 57s
-
3. Model Doors, Windows, and Stairs
-
Model doors with glazing7m 56s
-
Model a window5m 24s
-
Copy window groups2m 26s
-
Subobject manipulation5m 59s
-
Model stairs from plans5m 3s
-
Support the handrail6m 12s
-
-
4. Model Terrain Surfaces
-
Sculpt a sloping terrain4m 55s
-
5. Model the Second Floor
-
Extrude a walkway3m 33s
-
Create door headers1m 46s
-
6. Complete the Second Floor and Roof
-
Build interior partitions3m 47s
-
Cut window openings5m 20s
-
Create custom windows7m 35s
-
Build roof surfaces4m 41s
-
-
7. Model the Tower
-
Build the tower walls1m 37s
-
Build clerestory windows3m 46s
-
Model the tower walls4m 32s
-
Shell the tower2m 43s
-
-
Conclusion
-
Next steps43s
-
- Mark as unwatched
- Mark all as unwatched
Are you sure you want to mark all the videos in this course as unwatched?
This will not affect your course history, your reports, or your certificates of completion for this course.
CancelTake notes with your new membership!
Type in the entry box, then click Enter to save your note.
1:30Press on any video thumbnail to jump immediately to the timecode shown.
Notes are saved with you account but can also be exported as plain text, MS Word, PDF, Google Doc, or Evernote.
Share this video
Embed this video
Video: Subobject manipulation