Start learning with our library of video tutorials taught by experts. Get started
Viewers: in countries Watching now:
mocha has always been very popular as a tracking tool, but with the rising interest in stereo 3D conversion, its rotoscoping capabilities have become a favorite player in that pipeline and sales have soared. In this course, Steve Wright covers the basics of operating mocha, as well as advanced tracking and rotoscoping techniques. The course also covers the mocha/Nuke stereo 3D production pipeline in detail.
In an earlier video we saw how to pull out the feathered edge on individual control points. The Edge Properties panel over here, however, can set an overall edge feather for the entire matte, as well as unable motion blur. But first we'll need a Spline, so I'll grab a X Spline, draw a Spline here. Notice with the Spline selected the Edge Properties are all lit up. If we deselect, there is no selected Spline, they're ghosted out. So, we'll select the Spline again. To see how it works, we're going to need to see our Matte, so we'll turn the Mattes on, the Alpha channel off, and the Paint box off. We'll move down here and zoom in real tight.
To see the Edge Width, I'll turn off the Spline display, and now we can see the hard edges. We'll start with Edge Width. Whatever value is in this window, you have two modes. You can either set it to that value, so I've set the Edge Width to 3, or you can add that value. So, I've added 3, added 3, added 3. If I change this to 5 and click Set, now I have set the width to 5. So I can add 5 to the Edge Width several times, so I can show you this neat feature.
If I put in a negative 2 tab, I click Add, it'll actually subtract 2, and I can walk down to the feathered edge a little at a time. If you want to eliminate the feathered edge, then just the Edge Width value to 0, then select Set and that will set the Edge Width to 0. Now I'm going to turn the Splines back on the show you this feature. If you have one or more Splines selected then your Edge Width will be applied just to those. This will set those to 5.
I'll select these two and I will Add 5 and Add 5. I'll deselect all control points, and set the Edge Width to 0, so I can show you about a single feathered point. I'll select the Edge tool and pull out one control point. Now with this one control point selected, if I set the Edge Width to 5 and then say Add, it will add 5 to just that one feathered point. And if I ever want to set a feathered control point back to 0, just make sure you've selected that point, set the Edge Width to 0, and click Set.
Now let's take a look at the Motion Blur. To do that I'll need a little motion. So I want to move my playhead to Frame 2, click to deselect all control points, then I'll use Q to move the Translate tool, and Shift my Spline over. I've got two frames in animation. If I turn on the Motion Blur, nothing happens. The reason is with the OpenGL render like this, you don't see motion blur. You can see feathered control points or edge width, but not motion blur.
To do that we're going to have to look in the clip pop-up list. So first, we have to put the viewer back to RGB, turn off the Mattes display. Then, we come over to the clip pop up and we select the Matte for Layer 1. That's the clip we want to see. Select that, and now we're seeing the fully rendered matte, including the motion blur. I'll turn Motion Blur off and on, and again, I'm going to turn the Spline display off, so we can see what we're doing better.
Some of the Motion Blur adjustments: the angle, 180, that's a standard film camera. 180 degrees shutter is typical and average. If you want to cut down on the amount of motion blur you lower the angle, so let's lower the angle let say 45 degrees and now the motion blur is recalculated much smaller. If you want to go bigger, you'd set that to maybe 300 degrees and now the motion blur is dramatically increased. The phase and quality parameters are not yet hooked up in Mocha 2.6. Now let's take a look at the Overlay Colors and see how we can use those, but let's go back to our Lantern Boy and re- home the viewer with the asterisk key.
I'll turn my one Spline back on and then I am going to need a new few more, so I'll draw couple of more Splines here, and here, another one here, and one more right there. When I deselect, all of these are purple. They get their color purple from the chip over here. I like a little more room for my layer list so I'm going to delete the layer properties out of here. Don't forget, we can bring them back right here, Layer Properties, there they are, but I like to see my entire layer list. I'm also going to darken the view down, so we can see our colors a little better, so I'm going to turn that down.
All right, so this purple Spline gets its color from this chip, which if I select it, has inherited it from here, the Unselected color. To change it, I just click on this chip, I'll select the Cyan color, click OK, and now when I deselect, this is colored Cyan, and this chip is Cyan. I'll do the same thing to Layer 2. Click on the unselected points, select Cyan, say OK. There. I've got two that are Cyan. These three here, I'd like to change them to a different group. So I can select from the screen, for example, click the Unselect Chip. I'll make them Orange. Click OK.
Select the next one, Unselected> Orange>OK, one more, Unselected>Orange>OK. Now I have two groups: a Cyan group and an Orange group. Now if you have a really large, complicated job, you might need a lot of different colors so you can actually dial up your own colors and make a palette like this. I'll select Layer 1, select the Unselected chip. We'll go over to the color picker here.
Now here I can dial up any color that I want, so I'll select a big deep blue, I'll click and drag that chip down here onto the pallet. Now, when I click OK, that's turned deep blue. I'll select this one, the Unselected chip, and I'll just click on that pallet chip that I made. Click OK. Assigning colors to groups of Splines like this can help you keep a large job much more organized.
There are currently no FAQs about mocha 2.6 Essential Training.
Access exercise files from a button right under the course name.
Search within course videos and transcripts, and jump right to the results.
Remove icons showing you already watched videos if you want to start over.
Make the video wide, narrow, full-screen, or pop the player out of the page into its own window.
Click on text in the transcript to jump to that spot in the video. As the video plays, the relevant spot in the transcript will be highlighted.