Easy-to-follow video tutorials help you learn software, creative, and business skills.Become a member
If you'd like to draft using architectural measurements, it's important to know that AutoCAD can be a little bit picky in how you enter your values. In this lesson, we're going to learn the proper format for entering distances using architectural measurements. On my screen, I've got a drawing of a floor plan for a college dorm room. This drawing was created using architectural units. We can verify that by visiting the Drawing Units dialog box. Let's go there quickly. I'm going to open up the Application menu. I'll come down to Drawing Utilities, and I'll select Units. We can see right here this drawing is set to Architectural.
I'm going to click the X to close this. What I'd like to do in this lesson is take the geometry that's been drawn in this bedroom and recreate that geometry in this bedroom. In creating the new geometry, we'll be entering our distances using architectural measurements. I'm going to start out by zooming in a little bit. I'll make this geometry a little larger on screen. We'll create this rectangle first. This shape represents a twin-size bed. The standard measurements for a twin-size bed are 6'-3" x 3'-3".
I'm going to move up and launch the Line command. Then I'll move over into this bedroom, and I'm not very concerned about trying to match the distance away from the wall right now. I'm just going to pick a point right about here. To draw this as accurately as possible, I'm going to lock my Ortho. I'll come down and click that Toggle on my Status Bar. I will then pull down and I am now ready to enter my first measurement. I'm going to type 6, and then I'll press the apostrophe key. AutoCAD needs the apostrophe to recognize that we're entering feet. I will then enter my inches followed by a quote symbol.
The quote is the same key as the apostrophe, you just have to hold down your Shift key. The quote symbol lets AutoCAD know that we're entering inches. I will then hit Enter to finish my line segment. I'm going to pull to the left here and I'll type my next distance 3'3", Enter. I'll pull up and type 6'3". Notice that we're entering the values very similar to how an architect would write them on a piece of paper. Let me hit Enter to finish this line segment, and then I'm going to right-click and select Close to finish the shape.
Okay, let's do this next shape. This rectangle represents a small chest of drawers. I'm going to hit my Spacebar to go right back into the Line command. I'm going to pick my start point right about here. Let's trace this guy in a counterclockwise fashion. So, my first measurement is going to be 2'6", Enter. Now, notice this next value has whole inches and fractional inches. If there is anything tricky about this, this is what you would consider the tricky part. To enter this distance, I'll type 1'7-5/8".
Notice where I put the dash. I put it between the whole inches and the fractional inches. We have to do that, otherwise AutoCAD looks at it as 75/8, which is obviously incorrect. I'll press Enter to finish my line segment. Let's come back to the right here, 2'6", Enter. I'm not going to close this one. I'm going to finish it the hard way. I'll pull up and enter a distance of 1'7-5/8", Enter. Since I'm finished with my shape, I can hit the Esc key to cancel out of this command.
Always remember to separate the whole inches from the fractional inches with a dash. Now, you may be wondering if there are any shortcuts for entering architectural measurements. Well, there is one. If you're entering inches, it's not necessary to enter the quote. By entering a measurement without a symbol, AutoCAD will assume you're drawing in inches. I've got one shape left. Let's create this circle. This circle represents a lamp. I'm going to move up and launch the Circle command. I'll pick my center point right about here. The radius of this circle is 5-1/8".
So, I'll type 5-1/8, and in keeping with my shortcut, I'll leave off the quote. I'll just hit my Enter key, and AutoCAD will assume I'm drawing in inches. As you can see, entering architectural measurements involves a little bit of extra work on our part. It's still very simple, once we understand how AutoCAD wants us to enter the values.
Get unlimited access to all courses for just $25/month.Become a member
100 Video lessons · 12032 Viewers
56 Video lessons · 11435 Viewers
83 Video lessons · 9349 Viewers
109 Video lessons · 5214 Viewers
Access exercise files from a button right under the course name.
Search within course videos and transcripts, and jump right to the results.
Remove icons showing you already watched videos if you want to start over.
Make the video wide, narrow, full-screen, or pop the player out of the page into its own window.
Click on text in the transcript to jump to that spot in the video. As the video plays, the relevant spot in the transcript will be highlighted.
Your file was successfully uploaded.